Find Dry Sewage Pump, Sewage Water Pump, Horizontal Sewage Pump on Industry Directory, Reliable Manufacturer/Supplier/Factory from China.

Inquiry Basket (0)

The Latest Product Alerts Send Me

No Leakage Vertical Multisatge Centrifugal Water Pump

Basic Info

Model No.:  DL

Product Description



Model NO.: DL


Max.Capacity: 50-100 L/min


Material: Cast Iron


Assembly: Liquid Pumps


Start Up: Electric Pump


Application: Industry, Building


Media: Water


Theory: Centrifugal Pump


OEM: Ok


Trademark: Tongke


HS Code: 8413709990




Max.Head: >150m


Driving Type: Motor


Structure: Multistage Pump


Power: Electric


Type: Centrifugal Pump


Industry: Industry


Performance: No Leakage Pump


Standard: Yes


Head: up to 120m


Origin: China


DL series Vertical Multistage Centrifugal Pump Hydraulic Pump

Vertical, single suction, multistage, sectional and centrifugal ones and used for transporting pure water and the liquids below 85 C and with the physical and chemical natures similar to water's.



Our Advantage have to say!

Compact structure √

High efficiency √

Low noise √



Well use for Water supply, Buliding water supply, Fire-fighting ,Centralized heat supply system.



Running Data

Diameter DN 40-200mm
Capacity 6-300 m3/h
Head 24-280 m
Liquid Temperature up to 85 ºC
Operation pressure ≤ 30bar




√ Tongke Technical Design Description

Δ DL series Vertical Multistage Centrifugal Pump Hydraulic Pump is vertically structured, its suction port is located on the inlet section(lower part of pump), spitting port on the output section(upper part of pump), both are horizontally positioned. The number of stages can be increased or decreased per the required head at use. There are four included angles of 0 ,90 ,180 and 270 available for selecting per different installations and uses in order to adjust the mounting position of the spitting port (the one when ex-works is 180 if no special note is given).



Δ Major parts of the pump: inlet, middle and outlet sections, impeller, guide vane, guide vane on outlet bearing, shaft sleeve, balance drum and sleeve, link stand etc.

1. The inlet, middle and outlet sections, guide vane, guide vane on outlet section are all made of cast iron and mutually form the working room of the pump.

2. The impeller is made of cast-iron, Liquids go in from one side along with the shaft and an axial force may exist because unequal pressures on both front and back of the impeller.

Most of the force is made balanced by the balance drum while its residual is supported by the ball bearing on the upper end of the shaft.

3 The shaft is made of qualified carbon steel and in its middle the impeller, balance drum and shaft sleeve are mounted, which are fixed with pins and shaft sleeve nuts on the shaft to form the rotor. On one end of the shaft a lower shaft sleeve is mounted, which is fitted with the plastic bearing, and on the other the ball bearing is mounted to support the rotor and on the top of it a clutch is mounted and directly connected to the motor.

4. Both balance drum and sleeve form the balance device of the pump and can be replaced when worn out.

5. The shaft seal can not only use soft filling but also be changed with mechanical seal, when using soft filling, the shaft sleeve can be replaced when worn out and, when as the mechanical seal, the pressure water inside of the balance room is used for lubrication and cooling. When as the filling seal, the 3/8'' flexible union on the

outlet section is used through the flexible pipe to drain the water leaked from the filling body to the underground ditch to keep the place around the pump clean.

6. The bearing on the upper end of the pump uses molybdenum disulfide grease for lubrication.



√ Structural Diagram for DL series Vertical Multistage Centrifugal Pump Hydraulic Pump

No Leakage Vertical Multisatge Centrifugal Water Pump
1 section casing
2 seal ring/seal pad
3 stage casing
4 impeller
5 balancing sleeve
6 balancing piston
7 discharge casing
8 shaft
9 mechanical seal/filling body 10 shaft sleeve
11 water retaining sleeve
12 bearing support
13 thrust ball bearing
14 bearing cover
15 linkage stand
16 coupling
17 mechanical seal/gland cover 18 balancing pipe part
19 last-stage guide vanes
20 guide vane
21 water lubricated bearing sleeve 22 sand-proof tube
23 water lubricated bearing body 24 submerged bearing
25 Drainage wire-jam 26 water lubricated bearing cover






Attention: More detailed technical data for this pump please contact Tongke.



Main parts for Multistage Centrifugal Pump Hydraulic pump

Part Material
Shaft seal form Packing gland or Mechncial sesal
Impeller Cast iron, Ductile iron, Carbon steel , Stainless steel, Bronze, Duplex SS
Bearing Qualified China Bearing or NTN/NSK/SKF
Shaft 2Cr13, 3Cr13, Duplex SS


Attention: Particular material for project please contact Tongke engineer for suggestions.



Company Image for Tongke

No Leakage Vertical Multisatge Centrifugal Water Pump



Production Process



No Leakage Vertical Multisatge Centrifugal Water Pump

International Certificate

No Leakage Vertical Multisatge Centrifugal Water Pump



Service

Twenty years design and engineering experience and More than ten years over sea market Experience. Tongke provide most professional and thoughtful Pre-sales and After service.

Technical training Equipment evaluation

Installation and debugging Troubleshoot

Maintenance Update and improvement

Commitment to the service

1.One-year warranty. Provide technical support free all-life of the products.

2.Keep all-life contacting with clients, get feedback on use of the equipment and make the products quality continually perfected.

3.Hot-line of service is available in 24h, responded in 8h.



Your call and mail is welcome at any time

Contact Mr Seth Chen
Telphone 0086-13817768896

Contact us if you need more details on Water Pump. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Centrifugal Pump、Pump. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Pump

Email to this supplier
  • *Subject:
  • To:

  • *Messages:
    Your message must be between 20-8000 characters